Right-Sizing DC Power for Basement and Underground Telecom Rooms
2026/11/17
Right-Sizing DC Power for Basement and Underground Telecom Rooms
Background
An enterprise network operator was upgrading the connectivity infrastructure for a large commercial complex. The building's telecom rooms were located in the basement levels, housing optical transmission equipment, access switches, and a small battery bank for backup power.
Unlike rooftop or outdoor macro sites, these basement rooms had limited physical space, restricted access for heavy equipment, and no dedicated HVAC system. The operator needed a compact, self-contained power solution that could fit into a standard rack while managing its own thermal environment.
The Challenge: Space, Heat, and Access in a Confined Room
The operator faced three specific constraints.
1. Rack Space Limitations
The basement rooms were designed to house the building's core IT and telecom racks. Available floor space was minimal, and the power system had to fit within a standard 19-inch rack without displacing the transmission and switching equipment. Existing power shelves were too tall, consuming 4U to 6U of valuable rack height.
2. Heat Dissipation Without HVAC
The rooms had no active air conditioning. The equipment generated heat, and the sealed environment meant that heat accumulation was a real risk. The power system needed to be highly efficient to minimize waste heat, and the enclosure required its own cooling strategy.
3. Maintenance Access
Basement rooms were not easily accessible for large equipment or frequent maintenance. The power system needed to support front-access maintenance, and the controller needed to provide clear local diagnostics so that technicians could resolve issues without specialized tools.
The Solution: A 2U High-Density Power System in a Compact Cabinet
The operator selected a 5.22kW DC power supply cabinet that integrated a 2U rectifier system into a compact 16U enclosure.
1. 2U Rectifier System with N+1 Redundancy
At the heart of the cabinet is a 2U rectifier system delivering 5.22kW of -48V DC output. The system consists of three 1.74kW rectifier modules operating in an N+1 redundant configuration. This means that if one module fails, the remaining two modules continue to supply power without interruption.
The 2U form factor was the key enabler. By reducing the power system's rack height from the conventional 4U-6U to just 2U, the operator freed up valuable rack space for additional transmission equipment.
2. High Efficiency and Thermal Insulation
The rectifier system achieves conversion efficiencies exceeding 96%, which directly translates to lower heat dissipation. The cabinet is constructed with 1.2mm galvanized steel and lined with 20mm thermal insulation cotton, reducing heat transfer from the surrounding environment. A 500W air conditioner, mounted on the cabinet door, maintains internal temperatures within the operating range of the equipment.
3. Comprehensive Monitoring and Local Display
The system's controller provides 3 analog inputs (2 for battery temperature, 1 for ambient temperature), 7 digital inputs for external status monitoring, and 6 digital outputs for alarm signaling. An LCD display on the controller provides real-time monitoring and configuration options for technicians on site.
Communication is supported through RS485 and SNMP, allowing the system to be integrated into the building's network management system. This enables remote monitoring of the power system from the operator's central NOC, reducing the need for physical visits to the basement rooms.
4. Front-Only Access and Security
The cabinet features a single front door with front-only maintenance access. The anti-theft three-point locking system and concealed inner hinges provide security for the equipment inside. The 150mm plinth raises the cabinet off the floor, protecting it from minor water ingress and simplifying cable routing through the bottom entry.
The Results
The deployment met the operator's requirements for space efficiency, thermal management, and remote visibility.
The 2U rectifier system allowed the operator to install the power system without displacing existing transmission equipment. The high efficiency of the rectifiers, combined with the insulated cabinet and 500W air conditioner, maintained stable internal temperatures even without building HVAC.
The SNMP communication capability gave the operator full visibility into the power system's status, including battery temperature and ambient conditions. Alarms for over-temperature, module failure, or battery issues were received at the NOC in real time, allowing the operator to dispatch maintenance only when necessary.
The front-access design and clear LCD display simplified on-site maintenance, reducing the time required for technician visits.
What This Case Demonstrates
In confined spaces such as basement telecom rooms, the power system must be designed for the constraints of the environment, not just the electrical requirements of the load.
A compact 2U rectifier system with N+1 redundancy provides the reliability of a larger system without the rack space penalty. High efficiency and insulated cabinet construction reduce the thermal burden on the room, and the integrated air conditioner maintains a stable internal environment for the equipment.
The combination of local LCD diagnostics and remote SNMP monitoring ensures that the system can be managed effectively, even when the site is difficult to access.